Fotaku — est. 2023 · a hobby blog, not a shopLast updated: 2 November 2026

Fotaku

notes on photographing figures, kits & small things

Latest posts2026

Backdrops

The €4 backdrop that beat my €60 one

A roll of matte grey poster board from a stationery shop, curved into a sweep and taped to a shoebox. It shows fewer creases, kills reflections, and it doesn't smell like vinyl.

Continue reading

The expensive vinyl backdrop I bought last year has one problem nobody mentions in reviews: it's glossy enough to pick up the panels as two faint stripes. On a dark figure base that's fine. On anything with a white skirt it's a disaster you only notice at 100% zoom.

Matte poster board is the opposite. It drinks light, so you'll need maybe a third of a stop more exposure, but the gradient you get by moving the figure away from the sweep is smooth and controllable. Two pieces, a bit of masking tape on the back so the seam doesn't show, done.

Downside: it bends permanently if you store it rolled for more than a week. I keep mine flat behind the wardrobe now.

backdropbudget
Painting

My first resin garage kit: everything that went wrong

I washed it, I primed it, I airbrushed it, and then I sanded half of it back to bare resin. A list of mistakes so you can make different ones.

Continue reading

Mistake one: skipping the second wash. Release agent doesn't always come off with one scrub, and primer will happily sit on top of it for a day before peeling off in sheets.

Mistake two: thinning the skin tone too much. Three thin coats is good advice. Seven watery coats is how you get blotches that look like the figure has been in the rain.

Mistake three: photographing it before the gloss coat had fully cured. Everything looked fine in person. Under a hard side light, every fingerprint was right there.

It's sitting on my shelf now, and from about a metre away it looks great. I'm counting it as a win.

garage kitairbrushresin
Lenses

A 60mm macro vs. a flagship phone: closer than you'd think

Same figure, same light, same afternoon. The phone loses on fine detail and wins on convenience, and on a 6-inch screen nobody can tell which is which.

Continue reading

Where the dedicated lens still wins clearly: texture on matte surfaces, hair sculpts, and anything where you want shallow depth of field that doesn't look computed. The phone's portrait mode still cuts through thin parts like ahoge and weapon tips.

Where the phone wins: speed. I can shoot a whole shelf in ten minutes with the phone. With the camera, a tripod and focus stacking, one figure can take an evening.

My honest recommendation: shoot with what you have, and only buy a macro once you're annoyed by a specific limitation you can name.

macrophonecomparison
Technique

Focus stacking without special software

At 1:1 magnification even f/16 won't get a whole face sharp. Fourteen frames, a free stacking tool, and a remote shutter will.

Continue reading

Set the camera to manual focus, start at the nearest point (usually the nose or a hand), and turn the focus ring by the smallest amount you can manage between shots. Overlap is your friend, so take more frames than you think you need.

Don't touch the tripod between frames. Use a two-second timer or a remote. Even the click of the shutter button is enough to shift alignment at this scale.

Stack in any free tool that does alignment first. The halo artefacts around edges are normal; clean them up by hand with a soft brush on the source frame.

focus stackingmacro
Low key

Black backgrounds and one hard light

Turn every light off, keep one panel at 90 degrees to the figure, and pull the background at least a metre back. That's the whole trick.

Continue reading

The distance between figure and background matters more than how black the background is. Light falls off fast, so a mid-grey wall a metre and a half away will render as pure black when you expose for the figure.

Use a piece of black card on the opposite side as a flag. It deepens the shadow side and gives that sculpted look that's hard to get with soft, even light.

low keylighting
Guide · 11 min read

Lighting a 1/7 scale figure with two cheap panels and a sheet of baking paper

This is the guide I wish I'd had when I started. It's been rewritten three times as my setup changed, and this version reflects what's actually on my desk today. If you only read one section, read the one about distance.

The setup

Two bi-colour LED panels, one on each side, slightly in front of the figure. A sheet of baking paper clipped in front of each panel. A grey poster-board sweep behind. That's it.

grey sweep (backdrop) figure key (60%) fill (25%) camera

Why baking paper

Bare LED panels are small, hard light sources. They throw sharp shadows and leave little bright dots in glossy eyes and hair. Baking paper is cheap, slightly translucent, and diffuses evenly. It also doesn't yellow under LED heat the way some tracing papers do.

Clip it a few centimetres in front of the panel, not directly on it. The gap matters: the further the paper is from the LEDs, the more evenly the paper itself glows, and the softer the light.

Same figure, same settings. Bare panel on the left of the frame, diffused on the right. Look at the shadow under the chin.

Distance does more than power

Most beginners, including me, turn the brightness up when something looks wrong. Usually the fix is to move the light. A soft light close to the figure looks soft; the same light a metre away looks hard, because relative to the figure it's now a small source.

Move the light before you touch any setting on the camera.

My rule of thumb: the diffused panel should be about as far from the figure as the panel is wide. For a 20 cm panel, that's 20 to 25 cm.

Key and fill

Don't set both panels to the same brightness. Flat, even light makes figures look like product shots on a marketplace listing. Set one side (the key) noticeably brighter, and use the other (the fill) only to stop shadows from going completely black. I usually run around 60% and 25%.

Colour temperature

Set both panels to the same temperature and set white balance manually in the camera. Mixed temperatures look interesting on purpose and terrible by accident. I keep both at 5000K and adjust warmth in editing if I want it.

Camera settings, briefly

Tripod, base ISO, aperture between f/8 and f/16 depending on how much of the figure needs to be sharp, and whatever shutter speed gets the exposure right. With a tripod, slow shutter speeds are fine, just use a timer.

If you're on a phone: lock focus and exposure by long-pressing on the face, then pull exposure down slightly. Phones overexpose pale skin tones on figures almost every time.

What I'd buy first, in order

A tripod, then a second light, then a macro lens. The tripod changes everything about how carefully you can work; the lens changes the least.